- 您现在的位置：买卖IC网 > Sheet目录1248 > TISP5115H3BJR (Bourns Inc.)SURGE SUPP -90V UNIDIR DO-214AA
TISP5xxxH3BJ Overvoltage Protection Series
APPLICATIONS INFORMATION
AC Power Testing
The protector can withstand currents applied for times not exceeding those shown in Figure 8. Currents that exceed these times must be
terminated or reduced to avoid protector failure. Fuses, PTC (Positive Temperature Coefficient) resistors and fusible resistors are overcurrent
protection devices which can be used to reduce the current flow. Protective fuses may range from a few hundred milliamperes to one ampere.
In some cases it may be necessary to add some extra series resistance to prevent the fuse opening during impulse testing. The current versus
time characteristic of the overcurrent protector must be below the line shown in Figure 8. In some cases there may be a further time limit
imposed by the test standard (e.g. UL 1459 wiring simulator failure).
Capacitance
The protector characteristic off-state capacitance values are given for d.c. bias voltage, VD, values of -1 V, -2 V and -50 V. The TISP5150H3BJ
and TISP5190H3BJ are also given for a bias of -100 V. Values for other voltages may be determined from Figure 6. Up to 10 MHz, the
capacitance is essentially independent of frequency. Above 10 MHz, the effective capacitance is strongly dependent on connection inductance.
In Figure 12, the typical conductor bias voltages will be about -2 V and -50 V. Figure 7 shows the differential (line unbalance) capacitance
caused by biasing one protector at -2 V and the other at -50 V. For example, the TISP5070H3BJ has a differential capacitance value of 166 pF
under these conditions.
Normal System Voltage Levels
The protector should not clip or limit the voltages that occur in normal system operation. Figure 9 allows the calculation of the protector VDRM
value at temperatures below 25 ° C. The calculated value should not be less than the maximum normal system voltages. The TISP5150H3BJ,
with a VDRM of -120 V, can be used to protect ISDN feed voltages having maximum values of -99 V, -110 V and -115 V (range 3 through to
range 5). These three range voltages represent 0.83 (99/120), 0.92 (110/120) and 0.96 (115/120) of the -120 V TISP5150H3BJ VDRM . Figure 9
shows that the VDRM will have decreased to 0.944 of its 25 °C value at -40 °C. Thus, the supply feed voltages of -99 V (0.83) and -110 V (0.92)
will not be clipped at temperatures down to -40 ° C. The -115 V (0.96) feed supply may be clipped if the ambient temperature falls below -21 ° C.
JESD51 Thermal Measurement Method
To standardize thermal measurements, the EIA (Electronic Industries Alliance) has created the JESD51 standard. Part 2 of the standard
(JESD51-2, 1995) describes the test environment. This is a 0.0283 m3 (1 ft3 ) cube which contains the test PCB (Printed Circuit Board)
horizontally mounted at the center. Part 3 of the standard (JESD51-3, 1996) defines two test PCBs for surface mount components; one for
packages smaller than 27 mm on a side and the other for packages up to 48 mm. The SMB (DO-214AA) measurements used the smaller 76.2
mm x 114.3 mm (3.0 ” x 4.5 ”) PCB. The JESD51-3 PCBs are designed to have low effective thermal conductivity (high thermal resistance) and
represent a worse case condition. The PCBs used in the majority of applications will achieve lower values of thermal resistance and so can
dissipate higher power levels than indicated by the JESD51 values.
“TISP” is a trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office.
“Bourns” is a registered trademark of Bourns, Inc. in the U.S. and other countries.
JANUARY 1998 - REVISED JANUARY 2007
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
TISP61089BDR
SURGE SUPP SLIC PROG HV 8-SOP
TISP61089BSDR-S
PROTECTOR QUAD PROGRAMMABLE
TISP61089HDMR-S
SURGE PROT THYRIST 155V SLIC
TISP61089QDR-S
PROTECTOR PROGRAMMABLE SLIC
TISP61089SDR-S
PROTECTOR OVER VOLTAGE
TISP6NTP2ADR
SURGE SUPP QUAD PROG SOP
TISP6NTP2C-R6-S
SURGE PROTECTOR QUAD PROG 90A
TISP7082F3SL
SURGE SUPP 66V BIDIR 3-SL
相关代理商/技术参数
TISP5115H3BJR-S
功能描述:硅对称二端开关元件 Forward Conducting Unidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA
TISP5150H3BJ
制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:FORWARD-CONDUCTING UNIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS
TISP5150H3BJR
功能描述:硅对称二端开关元件 Forward Conducting Unidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA
TISP5150H3BJR-S
功能描述:硅对称二端开关元件 Forward Conducting Unidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA
TISP5190H3BJ
制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:FORWARD-CONDUCTING UNIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS
TISP5190H3BJR
制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:FORWARD-CONDUCTING UNIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS
TISP5190H3BJR-S
功能描述:硅对称二端开关元件 PROTECTOR - SINGLE UNIDIRECTIONAL RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA
TISP5XXXH3BJ
制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:FORWARD-CONDUCTING UNIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS